Pages Menu
TwitterRssFacebook
Categories Menu

Posted by on Jun 3, 2015 in Maintenance advices, My Blog, Pool Filters |

9 Successful Steps for Cleaning a Pool

It is pool time. It’s the moment when you are weighing up your option on the best way to clean and maintain your swimming pool. For many, this means employing a professional service technician to perform the task once or twice a week. However, you can take care of your pool service riverside ca yourself using these nine simple tips.

Riverside Pool Service Tools1. Assemble Your Tools

Inspect the inventory of your pool cleaning supplies and ensure you have everything you need. Check the expiration dates on all pool chemical containers before you begin, and ensure you have all the basic accessories needed to clean the swimming pool in place.

2. Remove the Cover

During the winter and fall, your pool cover accumulated debris and water. Make sure you remove all the debris carefully from the pool cover before you start the cleaning process. Pool service riverside ca recommend that you use a submersible pump to siphon off the gathered rainwater. Once the water and debris are removed from the cover, clean the pool cover with a mild detergent mixed with water using a scrub brush, and lay it out flat to dry.

pool service Riverside CA filter3. Check Your Equipment and Filters

Remove any water in the tubes; unplug the piping both at the filter system area and in the pool. If possible, replace filter media when they are used for over two years. Make sure any plug and gasket is in good condition. Generally, inspect all the equipment thoroughly for proper installation and operation by consulting reputable riverside pool service company.

4. Brash the Sides and Ledges

Every week, brush the sides and bottom of the pool before you run the pump. The debris that was clinging to the sides will be suspended in the water and will exist through or caught by your filter medium.

5. Filter and Circulate

Regardless of the size of the solids, they must be filtered out of the pool water. Remove the particles faster before they have the chance to become part of sludge on the bottom of the pool. If you allow these solids to be in the pool water, they will contribute to the growth of algae and bacteria, which eventually changes the water chemistry in the pool. The basic principle is to pump the water under pressure through the filter medium to capture and remove all the solids before running the filtered water into the pool. Depending on the speed of the pump and the size of the pool, you should run the filtration cycle for at least two hours.

6. Clean the Bottom

Perform a weekly cleaning in the summer, or as required in the winter, using a bottom cleaning system such as an electric underwater robot, pop-ups, a vacuum on a pole or a pump-driven vacuum. Take your pick, but ensure it is working so that your pool is cord and horse-free.

7. Backwash Your Filter

A solid filter should be back-washed monthly. Cartridge filter must be removed or replaced regularly. For other filter, read the manual instruction, but never use it more than three years.

8. Test the Water

Now that your pool water is relatively clear, check the chlorine and PH levels with a testing kit and adjust to proper levels. Ideally, the chlorine levels should be between 2.1 and 4.0 parts per million, while the PH levels should be between 7.1 and 7.9. Remember, do not mix various swimming pool chemicals and always read the instructions given by the manufacturer.

9. Shock the Pool

Chlorine shock products are available in granular and solid form. You need to add the right amount to raise the chlorine level of the pool to about 3.0 parts per million. Don’t just throw chlorine directly into the pool as this might cause staining or bleaching of the liner. Allow the pool to run for 24 hours after chlorination and then retest the chemical properties of the water in the pool.

Enjoy your pool!

Read More

Posted by on May 29, 2015 in Pool Filters |

The Basics of Swimming Pool Filters

Desjo_Banner__0001_PipelessFiltrationSystem

Swimming pool water should always maintain a high level of cleanliness for the safety and health of people who use the pool. To maintain such a level can be sometimes hard, if you don’t know how to do it. That is where swimming pool filters should help you out on. Swimming pool filters are the backbone to a clean and hygienic pool. With all the circulation system of the swimming pool in place, it is better to have a fully effective and functioning filter to regularly clean and get rid off any dirt. But how do you know and do all that? It is only by understanding the basics of swimming pool filters.

Here, you are going to get the basics of the filters you need you have with you as you deal with your swimming pool filters. So, let us start!
What are swimming pool filters?Swimming pool filters are the mechanical devices in the pool’s water circulatory system that help in filtering off the waste from pool water. They are used to trap debris, papers and other waste products brought in the swimming pool by swimmers or wind in order to maintain the pool at a healthy state.

BW58221-bestway-2500-gal-flowclear-swimming-pool-filter-pump-big
What are Basic Types of Swimming Pool Filters?There are 3 basic types of filters, namely:
•Sand Filter. This is a filter that consists of sand which is used to trap the impurities of the water. Water enters the filter through a multi port backwash valve and its impurities are captured by the sand in the filter. There are horizontal separate drains called laterals, where water passes through, all the way to the drain pipe at the bottom of the tank.There is where it comes out of the filter.
•Diatomaceous Earth Filter. This is a filter that has a gird full of series of fabric all over it. The fabric itself has a coating of Diatomaceous Earth, which is a white powder found in many ground deposits.The powder acts as the media of infiltration, as the water passes through it, leaving the impurities behind.Even the very microscopic substance are filtered.

There are 2 types of Diatomaceous filters usedhayward_tank

1.Spin Filters – These filters are made of wheel shaped grids aligned horizontally. They have been extensively used in the old swimming pool systems.
2.Vertical Grid Filters – These are filters that are made up of grids attached vertically on a manifold. Here, water enter from the tank’s bottom part, to the exteriors of the grids and finally out of the filter.
•How do Swimming Pool Filters Work? Almost all the different varieties of filters have a similar operating system.They all use the same principle in eliminating the waste in the pool’s water.Basically, filters are to get rid of impurities, and to do that, they follow the water’s circulation system. Here is the whole process of how filters works:
-Water enters the filter through its inlet.-As water increasingly goes in, more dirt is trapped.-As more and more dirt is trapped, the back pressure of the valve increases. (This can be seen in the backwash cave pressure gauge.)-After the all the dirt has been removed, water exits the filter through the outlet.

Read More